How to Change Spark Plug Wires in Vehicles

by Contributing Writer; Updated June 12, 2017

The Vehicles has several different engine options available, but no matter what engine is in yours, the process of changing the spark plug wires on your Vehicles is the same. The spark plug wires are critical to the operation of the ignition system as they carry the electrical charge from the distributor or coil pack to the spark plugs. A faulty wire will allow a drop in voltage or may not deliver any, causing the plug to fire with a weak spark or not fire Vehicles all. If you suspect the wires are defective, replace them with a new, high quality set of wires.

Under The Hood:

 How to Change Spark Plug Wires in a 1500 Goldwing

Locate the spark plugs by removing the side plates on the right and left sides of the Goldwing's engine. Grab hold of a single spark plug wire, just below where it attaches to the actual spark plug, and give it a gentle pull. The wire should pop right out.

Follow the spark plug wire to its opposite endpoint, where it connects to the distributor. Pull gently to fully remove the wire.

Install the new wire by snapping it into place at the spark plug end and the distributor cap end. It's better to do one spark plug wire at a time, rather than get them mixed up and risk engine problems, so finish one wire before moving on to another.

Repeat this process for the remaining spark plug wires and replace the side plates on your Goldwing's engine.

Items you will need

  • Spark plug wires

 How to Change Spark Plug Wires on a Ford Explorer

Open the hood of your Explorer and locate the negative battery cable at the battery terminal. There is a large minus symbol on the battery indicating the negative post or terminal. Loosen the retaining bolt on the negative cable end, then remove the cable from the battery. Isolate the cable end to avoid it accidentally energizing the ignition while you are working.

Locate the spark plug wires on the engine. Older models that have a distributor will have wires running from it and connecting to the spark plugs on the other end. Newer models will have a coil pack and no distributor. These systems have spark plug wires running from the coil pack directly to the spark plugs.

Select the first spark plug wire to change. It really does not matter where you start, but do not take off more than one wire at a time. If you mix up the location of the wires, the engine will not run right, if at all.

Grasp the spark plug wire at the boot on the distributor or coil pack. Twist it slightly as you pull straight off the terminal. Do not pull on the wire or you may rip the wire out of the boot. Follow the wire down to the opposite end and, again, twist and pull from the boot to remove the wire from the spark plug.

Lay the old spark plug out straight on the ground or a workbench. Match the length of the old plug wire to one of the same length in the new set, then discard the old wire.

Install the new wire by placing a small amount of dielectric grease in each of the boots on the end of the wires and then pushing the wire onto the spark plug until it snaps in place. Route the wire up to the distributor or coil back and push the wire on the connector there.

Move to the next wire and repeat the process. Continue removing one wire at a time, replacing them with new ones and working around the engine until they have all been changed.

Connect the negative battery cable to the negative terminal on the battery, then tighten the retaining bolt with a wrench. Start the engine to verify that it is running properly and that all the plugs are routed correctly. Close the hood.

Items you will need

  • Wrench set

  • Dielectric grease

 How to Change the Spark Plug Wires on a Chevy Malibu

Raise the hood of your Chevrolet Malibu. Remove the negative battery cable with a wrench.

Select a spark plug as a starting point. Grasp the rubber boot at the top of the plug. Twist the boot while pulling up to remove the rubber boot from the spark plug. Follow the wire to the opposite end and grasp the boot. Twist and pull up on the boot to remove the wire.

Select a wire of matching length from your set of replacement wires. Set the old wire aside. Apply a drop of dielectric grease to the boot on each end of the wire. Press one end of the wire onto the empty terminal on the distributor until it clicks in place. Press the opposite end of the wire onto the spark plug until it clicks.

Repeat the process for each wire, removing only one at a time. Avoid removing more than one wire as this can result in confusing the firing order, causing engine damage.

Replace the negative battery cable and tighten it with a wrench. Close the hood of your Malibu and start the engine to test it.

Items you will need

  • Wrench set

  • Spark plug wires (specific for your engine)

  • Dielectric grease

About the Author

This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more about It Still Runs, contact us.